manualshive.com logo in svg

NEC Express5800/R320a-E4, Руководство пользователя

Поделиться
Скачать
NEC Express5800/R320a-E4 Скачать руководство пользователя страница 125

Windows Setup 4-75

 

Setup of receiving SNMP packets from specific hosts only   

Select [Accept SNMP packets from these hosts], specify IP addresses of the hosts, IP 
addresses of the servers to install NEC ESMPRO Agent, and the loop-back address 
(127.0.0.1). 

Setup of receiving SNMP packets from specific communities only 

Change the name of the community receiving SNMP packets from the default “public” 
to any name. 

IMPORTANT:

   

„

 

If the community name is changed, you must change the registered community of 

NEC ESMPRO Agent from [Control Panel]. To change the community to another 
and register it, use the [SNMP Community] list box in the [General] tab. 

„

 

To allow NEC ESMPRO Agent to receive SNMP packets sent from NEC 

ESMPRO Manager, set the send community name in NEC ESMPRO Manager to 
be the same as that accepted by the SNMP Service in NEC ESMPRO Agent. 

7. 

Terminate the network setup. 

IMPORTANT: 

„

 

If the SNMP service is added to the system after the service pack had been applied 

at OS installation, apply it again. If not, the SNMP service may not operate 
properly. This can cause the improper operation of NEC ESMPRO Agent. 

„

 

The SNMP Service is required for operating NEC ESMPRO Agent. If the SNMP 

Service is deleted after the installation of NEC ESMPRO Agent, install the SNMP 
Service and then reinstall NEC ESMPRO Agent. 

„

 

Some software products provided by other vendors may change the SNMP Service 

configuration. If you install NEC ESMPRO Agent on the system under the 
condition where these types of software are already installed, NEC ESMPRO 
Agent service may not work properly. 
In such a case, delete the SNMP Service once and then install the service again. 
Afterwards, reinstall NEC ESMPRO Agent and the software products provided by 
other vendors. 

 

Содержание Express5800/R320a-E4



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды