Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя | Manualshive

Страница: 34 / 172

background image

Global Array Manager (GAM)Server Software for NetWare 4.11/4.2 and 5.0

2-14

Disk Array Controller Software Kit User’s Manual

• (For NetWare 4.11/4.2): Uncomment the

load aspitran

command line.

• (For NetWare 5.0): Modify the NWASPI.CDM line by specifying

the pathname for the exact location of NWASPI.CDM.

• If you wish to enable RAID Fault Management (RAIDBUILD) and

optionally change its default parameters, you need to modify the
RAIDBLD command line installed in AUTOEXEC.NCF. Refer to
Appendix C: “RAID Fault Management” for information.

• If you will be using drives from more than one vendor in the same

RAID Group, refer to Appendix E: “The MYLEXDRV.SIZ File” for
information on setting drive size limits for consistency across
multiple vendors’ drives.

7. Be sure to remove comment markers (such as the character #) from any

command line which you intend to enable.

8. Save the modified AUTOEXEC.NCF and exit.

9. Create a user account called

gamroot

. Assign Supervisor access

privileges to that user account.

10. Restart the server. See “Running Global Array Manager Server” on

page 2-15 after verifying correct server software installation.

«
...
32
33
34
35
36
...
»

Содержание Disk Array controller Software Kit 2.01













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Disk Array controller Software Kit 2.01

PM1D Manager V2

Бренд: Yamaha Страницы: 24

CONTRIBUTE 3 - USING AND ADMINISTERING...

Бренд: MACROMEDIA Страницы: 256

Бренд: Altigen Страницы: 19

Бренд: R&S Страницы: 262

NeatWorks For Mac

Бренд: NeatWorks Страницы: 33

DIMAGE VIEWER 2.1

Бренд: Minolta Страницы: 84

MELSOFT FR Configurator2

Бренд: Mitsubishi Electric Страницы: 230

Бренд: Siemens Страницы: 11

Бренд: Siemens Страницы: 28

Бренд: Siemens Страницы: 32

OpenScape Xpressions PhoneMail

Бренд: Siemens Страницы: 110

LINUX ENTERPRISE DESKTOP 10 SP1 -

Бренд: Linux Страницы: 76

Бренд: Kinoma Страницы: 6

CLUSTER MANAGER - INSTALLATION AND

Бренд: Red Hat Страницы: 190

Бренд: ArcSoft Страницы: 6

Portal Server ETV v4.2

Бренд: VBrick Systems Страницы: 64

Бренд: Intel Страницы: 192

Бренд: TomTom Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды