Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя | Manualshive

Страница: 152 / 172

background image

Installing TCP/IP - NetWare

B-2

Disk Array Controller Software Kit User’s Manual

Installing TCP/IP - NetWare

TCP/IP is included with NetWare 4.1x. and above. To install TCP/IP,
complete the following procedure. Refer to the Novell documentation for
more information.

1. Type the following command from the server console prompt:

LOAD INETCFG.NLM

↵

The system asks you if it should transfer the load commands from
AUTOEXEC.NCF.
Type YES. The Internetworking Configuration screen appears.

2. Highlight Protocols with the arrow keys and press Enter. The Protocol

Configuration menu appears.

3. Highlight TCP/IP and press Enter. The TCP/IP Protocol Configuration

menu appears.

4. Highlight TCP/IP Status and press Enter.

5. Move the status arrow to TCP/IP Enabled and press Enter.

6. Press the Esc key. The system prompts you to save the settings.

Select YES.

7. Press the Esc key until the Internetworking Configuration screen is

shown.

8. Highlight Bindings and press Enter. The Configured Protocol to

Network Interface Bindings menu appears.

9. Press Insert to add the new Binding.

10. Select TCP/IP from the list of protocols. The Binding TCP/IP to LAN

Interface menu appears.

11. Enter the Local IP Address. Be sure to follow the rules that exist for IP

addressing (see “IP Addressing” in the NetWare documentation).

12. Enter the Subnet mask (default is FF.FF.FF.0).

13. Press the Esc key. The system prompts you to save the settings.

Select YES.

14. Save settings and restart the NetWare server

15. Test the Server using the “Ping” command from a workstation. If the

systems are correctly configured, a reply is received.

«
...
150
151
152
153
154
...
»

Содержание Disk Array controller Software Kit 2.01













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Disk Array controller Software Kit 2.01

Linear-Phase MultiBand Software Audio Processor

Бренд: Waves Страницы: 27

Бренд: Acuma Labs Страницы: 20

Бренд: McAfee Страницы: 2

Бренд: Altigen Страницы: 19

Бренд: ARTEX Страницы: 33

Scarbee Clavinet & Piano

Бренд: Native Instruments Страницы: 24

Бренд: PNY Страницы: 15

CERTIFICATE 8.0 RELEASE NOTES

Бренд: Red Hat Страницы: 34

Anti-Virus Business Edition 2011

Бренд: AVG Страницы: 267

Бренд: FujiFilm Страницы: 3

CREATIVE 4D EXPRESS MONOGRAM WIZARD

Бренд: Pfaff Страницы: 2

POLICY MANAGER PROXY -

Бренд: F-SECURE Страницы: 43

Cassiopeia Pocket PC

Бренд: Zio Interactive Страницы: 17

Бренд: GNOME Страницы: 213

Digital Audio Effects Processor Doubler

Бренд: Waves Страницы: 6

FLASH REMOTING MX

Бренд: MACROMEDIA Страницы: 180

FLASH MEDIA SERVER 2

Бренд: MACROMEDIA Страницы: 234

Бренд: MACROMEDIA Страницы: 412

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды