Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя

Страница: 153 / 172

Installing TCP/IP

Manual No. 771929

B-3

A
P
P
E
N
D
I
C
E
S

Installing TCP/IP - Windows NT

TCP/IP is included with Windows NT. To install TCP/IP, complete the
following procedure.

1. Select Control Panel from the Main program group.

2. Double-click the Network icon.

3. Select Add Software.

4. Highlight TCP/IP Protocol and Related Components and click the

Load Software button.

Configuring the IP Address

1. After loading the software, click the Configure button.

2. Enter an IP Address for the network card. Be sure to follow the rules

that exist for IP addressing.

The Subnet Mask is generally set for 255.255.255.0.

For information on IP addressing, refer to the Windows NT
documentation.

3. Save all settings.

4. Shut down and restart the server.

5. Test the Server using the “Ping” command from a workstation. If the

systems are correctly configured, a reply is received.

Содержание Disk Array controller Software Kit 2.01













































































































































































Результаты поиска

Содержание Disk Array controller Software Kit 2.01

Отзывы:

Похожие инструкции для Disk Array controller Software Kit 2.01

Бренды по названию

Популярные бренды

Mylex Disk Array controller Software Kit 2.01, Руководство по установке и инструкция пользователя

Результаты поиска

Содержание Disk Array controller Software Kit 2.01

Отзывы:

Похожие инструкции для Disk Array controller Software Kit 2.01

Бренды по названию

Популярные бренды