Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя

Страница: 35 / 172

NetWare

Manual No. 771929

2-15

N
E
T
W
A
R
E

Verifying Correct Server Software Installation

In Case of Problems...

Problem: The message “Error in connecting selected server” is

displayed or an error is encountered when trying to
connect to a server.

Check:

Is the IP address correct?

Check:

Is the server software, GAMSERV.NLM, installed and
loaded on the server(s)? Use the following NetWare console
command to verify that the GAMSERV module is loaded:

modules

↵

Check:

Is the Ethernet connection good?

Check:

Is TCP/IP set up correctly? Try Ping to find the server.

Problem: Global Array Manager Server will not load.

Check:

Is the installation complete? The files GAMSERV.NLM,
GAMDRV.NLM, and GAMEVENT.NLM should be
contained in the SYS:SYSTEM directory of the server.

Running Global Array Manager Server

The Global Array Manager Server runs on the server and performs the
following functions:

• Monitors the controller(s) and disks in the server.

• Manages the controller(s) and associated disk subsystems in the server.

• Sends information to Global Array Manager Clients (if used).

Содержание Disk Array controller Software Kit 2.01













































































































































































Результаты поиска

Содержание Disk Array controller Software Kit 2.01

Отзывы:

Похожие инструкции для Disk Array controller Software Kit 2.01

Бренды по названию

Популярные бренды

Mylex Disk Array controller Software Kit 2.01, Руководство по установке и инструкция пользователя

Результаты поиска

Содержание Disk Array controller Software Kit 2.01

Отзывы:

Похожие инструкции для Disk Array controller Software Kit 2.01

Бренды по названию

Популярные бренды