MULTILIFT XR S Скачать руководство пользователя страница 67

Страница: 67 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

CXXX

dXXX

>>>>

Open the body locks

- push the ”bodylocks open” button

- under-run bar is retracted,

if it is not in

- URB signal light on the control

unit is lit, when the under-run bar

is fully in the in position

- when the locks are open, the “locks

not closed” signal light on the

control unit is lit.

Opening the body and tipping

locks

- move the control lever slowly

backwards

- under-run bar is retracted,

if it is not in

URB signal light on the control

unit is lit, when the under-run bar

is fully in the in position

- body locks will open

when the locks are open, the

“locks not closed” signal light on

the control unit is lit.

Drive the horizontal movement into

rear position

- push the rearmost button in the

bottom row on the either side of

the control unit

- horizontal movement slides

backwards (cylinder in)

- mechanical tipping lock opens

when the hook frame is in rear

position.

Horizontal movement into rear

position

- keep the control lever in rear

position

- horizontal movement slides

backwards (cylinder in)

mechanical tipping lock opens

when the hook frame is in rear

position.

Safety codes

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды