MULTILIFT XR S Скачать руководство пользователя страница 182

Страница: 182 / 210

XR21S59 CHU

182

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

Exit /

Off 1

OK /

Off 2

>>>

How to change the backlight setting of the buttons

The illumination strength of the backlight is set in the cab controller software. The buttons

to access the software and operations in the menu are as follows:

Note:

The first two buttons on

top of the cab controller are

the access buttons to the

software.

Normally these buttons are

identified as body locks

closed and body locks open.

The procedure of setting the illumination strength of the backlight is the following:

Press the first row buttons simultaneously for 10

seconds.

“

C002

” can be seen in the display while pressing the

buttons.

System will make 2 short beeps and all red LEDs will

be shortly lit.

A text “

tESt

” is shown in the display.

Press the top button on right (

locks open

button).

Sub menu up

(fast speed)

Sub menu down

(hook safety lock)

Press

10 s

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды