MULTILIFT XR S Скачать руководство пользователя страница 81

Страница: 81 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

NOTE 2!

NOTE 1!

Reverse the truck so that the rear part of the flatrack/body is above the trailer

or the platform.

The trailer or platform must be below the sliding level

of the hooklift equipment.

Check to be sure that the truck and the trailer/platform are in a straight line.

Engage the parking brake.

Engage the hydraulic pump.

If the vehicle is equipped with automatic air

suspension bleeding, then ensure that the sliding

level of the hooklift interchangeable body is not

below the level of the trailer or the platform.

MANUAL MODE

Choose manual mode A5

, push the A5 button for approx. 2 s.

Open the hydraulic body locks

- press the ”bodylocks open” button

- under-run bar is retracted, if it is not in

- URB signal light on the control unit is lit, when the under-run bar is fully

in the in position

- “locks not closed” signal light is lit on the control unit when the locks are open.

Drive the sliding frame to the rear position

- push the rearmost button in the bottom row on the left side of the control unit

- horizontal movement slides backwards (cylinder in)

- mechanical tipping lock opens when the hook frame is in rear position.

- start at idle speed and then increase the engine speed gradually.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды