MULTILIFT XR S Скачать руководство пользователя страница 139

Страница: 139 / 210

XR21S59 CHU

139

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Moving the liftframe onto the XR21S stowage

MIDDLE FRAME OF THE XR21S EQUIPMENT RESTS ON THE SUB FRAME AND

THE LIFTFRAME IS IN THE GRIPPING HOOK WHEN STARTING MOVEMENTS

It is recommended to let the engine run idle during

the stowage movements.

Check and, if necessary, push the locking shafts on the lower parts of the

liftframe to the STOWED position.

Engaging the stowage mode A4

Choose mode A4

2.1 push the A4 button shortly

2.2 code ”A4” is lit on the XR21S equipment control unit display

2.3 green signal light ”power on” is lit on the stowage control unit.

If it seems impossible to select the mode and code ”d019” is displayed on the

control unit, make sure that the attachment joints of the liftframe ratchets

are attached to the stowage.

Activate the handbrake.

Engage the hydraulic pump.

Moving the liftframe from the XR21S -gripping hook to the stowage

Code ”A4” is visible on the XR21S equipment control unit display.

Green signal light ”power on” on the stowage control unit is lit.

Press the STOW button on the stowage control unit without releasing it:

5.1

Body locks open

if they are still closed.

5.2

Horizontal movement moves to the stow/unstow position

horizontal movement stops in its far-front position.

>>>

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды