MULTILIFT XR S Скачать руководство пользователя страница 101

Страница: 101 / 210

XR21S59 CHU

101

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Opening the lift frame stowage lock

If the lift frame is in the XR21S hook (the liftframe has been picked up from

the immediate vicinity of the vehicle), continue to section ”Lifting the ISO

container”.

1. First rotate the middle sections of the ratchets enough to loosen them.

2. If needed, take the crowbar attached to the left side of the liftframe and

remove the dirt and ice from the areas where the ISO container and body are

attached.

The crowbar may also be used to extract the locking shaft. The locking shaft may

not be detached at this stage.

3. Turn the lock grips on the telescopic upper parts, on the surface of the lifting

frame’s vertical beams, into

OPEN position

(grips horizontally, images 3).

It is recommended to keep the lock grips in

OPEN position

when driving the truck

without an ISO container. The liftframe is then at its lowest.

4. Extract the locking shafts on the lower parts of the liftframe using the crowbar if

necessary. Turn the axis on both sides of the equipment to 180°

temporary

STOWED position

(lock plates vertical, images 4),

note

leave the whole pin

extracted so the liftframe can move in front of the stowage.

NOTE 1!

Leave the locking shaft into the

temporary STOWED position

only while you

remove the locking pin (phase 5), and then turn it into the

STOWED position

(phase 7).

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды