MULTILIFT XR S Скачать руководство пользователя страница 154

Страница: 154 / 210

XR21S59 CHU

154

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Construction

XR S hooklift equipment contains frames joined to each other which enable loading,

unloading and tipping of compatible Flatrack/bodies. The rear frame hinged to the rear end

of the sub-frame, which is fastened to the truck chassis, enables tipping of the Flatrack/

bodies (note: ISO Containers must never be tipped). The middle frame hinged to the rear

frame together with the hook arm sliding inside it, enable container loading and unloading.

Hydraulics

The configuration of the hooklift control valve comprises on the base plate situating,

electrically controlled directional valves, which distribute the oil flow to different cylinders.

There is one control valve for the hook arm and the locking cylinders and two for the

main cylinders. The main cylinder control valves operate at phases, depending on the

accessories, or at the same time and enable thus a more accurate control at slow speeds

and greater oil flow for simultaneous use.

There is a by-pass valve installed on the valve base plate, which is adjustable between

16 and 40 l/min. With this valve part of the oil flow is directed via the second valve of the

main cylinders back to the return line, and that is the way to obtain the accurate cylinder

movements when needed. The factory setting of the by-pass valve is 28 l/min. By turning

the valve close or open it is possible to obtain a slower motion of the main cylinder and to

adjust the speed of the hook arm cylinder.

The electrically controlled solenoid valve opens the free circulation flow, when no cylinder

movement is active.

The setting of the main pressure limiting valve is 300 bar, in addition of which the functioning

of the hydraulic locks and the hook arm out push pressure is limited to 180 bar.

There is a push button in the main cylinders’ first valve, the hook arm cylinder valve and

free circulation valve solenoid for possible emergency operation if the electrical current of

the hooklift disappears for some reason.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды