MULTILIFT XR S Скачать руководство пользователя страница 145

Страница: 145 / 210

XR21S59 CHU

145

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Schalten Sie die Einstellbremse und die Hydraulik ein.

Removing the liftframe from XR21S gripping hook

and leaving it on stand supports

LIFTFRAME HANGING FROM THE XR21S GRIPPING HOOK

WHEN STARTING THE PHASE

1. Drive the truck to the intended parking area.

The liftframe stand supports are not meant to be used

on uneven ground: a lifting frame laid on the supports

my fall over an cause damage.

MANUAL MODE A5

Choose manual mode A5

- push the A5 button for approx. 2 s

- green signal light ”power on” is lit on the stowage control unit.

Open the body locks

- push the ”bodylocks open” button

- “locks not closed” signal light on the control unit is lit, when the locks are fully

open.

Drive the horizontal movement cylinder in

- push the rearmost button in the bottom row on the either side of the control unit,

until the horizontal movement goes to the ISO container home position

(approx. 350 mm from the stow/unstow position of horizontal movement).

- mechanical tipping lock opens when the hook frame is in rear position.

Activate the handbrake and engage the hydraulic pump.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды