MULTILIFT XR S Скачать руководство пользователя страница 23

Страница: 23 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Flatrack/body

The demountable body can be a NATO STANAG 2413 flatrack, DIN 30722-1/2 flatrack

(max length 6650 mm), DIN 14505 flatrack (3765 mm locks, max 6650 mm), ISO IC & ICC

container or Swiss Standard pallet.

Check to be sure that the flatrack/body is suitable for the load to be transported. Generally

each flatrack/body has a model plate (ID) on which the length and permissible load are

specified.

Before picking up the flatrack/body, check that the hook height (H), tunnel height (T) and

the width (W) correspond with the XR hooklift dimensions and that the notches for the

body locks are in correct positions.

If there is even the slightest doubt of the flatrack/body dimensions, measure them first in

order to prevent the XR equipment and the flatrack/body from being damaged.

Gripping height (H), tunnel height (T) and width (W) of the flatrack/body can vary from one

flatrack/body to another. Note that they are country specific dimensions. If there is doubt

about the origin of the flatrack/body, the tunnel height and width must be checked in order

to ensure that they are compatible with those of the XR equipment.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды