MULTILIFT XR S Скачать руководство пользователя страница 170

Страница: 170 / 210

XR21S59 CHU

170

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

Hydraulics service

Do not carry out any repair if you do not know the item to be repaired.

Never carry out any service or repair on system under pressure.

Stop the truck engine always before tightening or repairing hydraulic connections.

Do not try to locate a hydraulic hose leak with your hands. A leak from a pressurised system

can penetrate the skin and cause serious injuries. A leak from a pressurised system can

also cause a fire when hitting a hot object.

Avoid skin contact with oil. Protect also your eyes.

Do not carry out work on hydraulic components under a raised frame. Use always a

mechanical support.

Do not remove any hydraulic components before supporting the frames and releasing

hydraulic system pressure.

Pipe connections, hose lengths and materials must conform with the Multilift requirements.

Use original Multilift spare parts or ensure otherwise that the components correspond with

the highest working pressure used.

Ensure that the oil corresponds with the requirements and ensure its viscosity and

cleanliness when adding oil into the system.

All changes to the recommendations concerning the oil and hydraulics must be verified

in writing with Multilift.

BE AWARE!

Servicing, repairs and installations of the hydraulic

components may be done only by persons trained for the jobs.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды