MULTILIFT XR S Скачать руководство пользователя страница 166

Страница: 166 / 210

XR21S59 CHU

166

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

• Inform the equipment operator of the start of the maintenance work.

• If the equipment is damaged or otherwise non-functional, ensure that it cannot be

started accidentally before and especially during the service work.

• Remove the truck ignition key and keep it in a safe place. Inform also others,

for example, with a warning sign.

• If there are several persons involved in the service work at the same time, the one

having the ignition key must inform everybody if, for example, the truck engine is

started or the hooklift functions are used.

If the work area is under the tipping frame, the equipment must be moved to loading

position.

Hooklift in rear position

If the work is done under the middle frame, the equipment must be moved to loading position

and the frames supported with separate tipping support in the correct places. Remember

to remove the support after the work has been completed.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды