MULTILIFT XR S Скачать руководство пользователя страница 133

Страница: 133 / 210

XR21S59 CHU

133

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

UNLOADING A HEAVY CONTAINER IN MANUAL MODE A5

Choose manual mode A5

, push the A5 button for approx. 2 s.

- green signal light ”power on” is lit on the stowage control unit.

Open the body locks

- push the ”bodylocks open” button

- “locks not closed” signal light on the control unit is lit, when the locks are fully

open.

Changing to automatic mode A3

Select automatic mode A3

- push the A3 button approx 2 s.

- “power on” signal light on the stowage control unit goes out.

When the control lever is moved back, first the XR21S equipment moves the

horizontal movement backwards and the middle frame moves back, just as

depicted in section

Unloading a flatrack/body

describing

automatic mode A1

Drive the middle frame to an approx. 20 degree angle

3.1 - move the control lever back (main cylinders out)

- ”frame not down” signal light is lit when the middle frame is lifted off the sub

frame

3.2 - stop the movement by releasing the control lever.

If the ISO container has a heavy load (more than 10 t) or its floor is extended, the beginning

of unloading should be done according to the following sections in

manual mode A5

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды