MULTILIFT XR S Скачать руководство пользователя страница 110

Страница: 110 / 210

XR21S59 CHU

110

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

>>>

Before gripping and loading the ISO container

CHECK THE ISO CONTAINER SUPPORT ROLLER POSITION ON THE XR21S

-EQUIPMENT BEFORE LOADING AN ISO CONTAINER!

LOADING AND UNLOADING AN ISO CONTAINER WITH A XR21S LIFTFRAME

HAS THE SAME PHASES AS HANDLING A FLATRACK/BODY.

THE DIFFERENCE BETWEEN HANDLING A FLATRACK/BODY IS,

THAT THE SUPPORT ROLLER CRADLES MUST BE IN CONTAINER

READY POSITION (image 1).

If the roller is in the flat rack/body change position (picture 2)

2 Pull the roller locking pins off (A).

3 Turn the front part of the roller to an upright position. Lock it to this position by

pushing the shorter locking pin into hole B. Push the longer roller locking pin into

hole C to the point, where you can still turn the roller.

4 Turn the roller to the flatrack/body

change position and push the

locking pin to the point where the

head of the pin goes into the

arched groove in the roller frame.

After the operation

both locking pins

must be

locked to

their correct

positions

with

lock latches

(picture 5).

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды