MULTILIFT XR S Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 210

background image

XR21S59 CHU

175

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

Safety

• Suitable eye and hand protection must be worn whilst carrying out this operation.
• Ensure suitable containers to hold the amount oil you will be draining are available

before starting this operation.

Environment

• Ensure oil waste oil is disposed of safely and in accordance with any local

environmental regulations.

Attention!

Ask the oil supplier for instructions. If you do not receive any

instructions, follow these recommendations:

Procedure

1. Completely empty the oil tank via the drain plug. Clean the oil tank carefully

from oil and contamination. On older systems with heavy contamination, it may

be necessary to remove the oil tank and flush out with a suitable flushing

agent.

2. Completely empty the hydraulic cylinders, tubes, hoses and the suction hose to

the pump.

3. Change the return filter.

4. Fill the tank with new oil via the return filter. Operate all cylinders carefully to

ensure that they will be filled with oil. Ensure that the pump is filled all the time.

Fill up the tank before it gets empty.

5. Drive for 2 or 3 days.

6. Check that all piston rods of the cylinders are in retracted position. Completely

empty the oil tank via the drain plug and change the return filter. Fill up the oil

tank with new oil and operate all cylinders carefully to ensure that they will be

filled with oil. Ensure that the pump is filled all the time. Check that the oil level

in tank remains in correct level.

Note!

Synthetic esters can dissolve old contamination. If the performance of

the hooklift appears to deteriorate before the oil filter change, inspect

the filters and change if necessary.

«
...
173
174
175
176
177
...
»

Содержание XR S



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XR S

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: T-Rex Страницы: 13

Бренд: Gamry Instruments Страницы: 69

Бренд: Rayger Страницы: 2

Aspect Q-CARD 100-4T

Бренд: idi Страницы: 38

Бренд: Tanco Страницы: 112

Бренд: Hach Страницы: 456

Бренд: Abus Страницы: 12

Littmann Classic II Pediatric

Бренд: 3M Страницы: 53

UG 2200 Special

Бренд: Amazone Страницы: 252

Бренд: HOFFEN Страницы: 22

Бренд: KEP Страницы: 33

ARIEDO HDC 300W

Бренд: GSi Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды