mru SWG100 CEM Скачать руководство пользователя страница 151

Страница: 151 / 155

MRU GmbH

SWG 100 User Manual

Page

151

155

The new created device can be found at the left side of the MRU4WIN screen.

Activated it and start the logging.

13.14.

Option: Connection the SWG100 with RS-485 converter to MRU4Win

It is possible to connect the SWG-100 to MRU4Win, via a RS-485 converter. For the connection

a MRU4Win-license and a RS-485 converter (offer-number: #62543) is required. Follow steps

must be done:

•

At the bottom side of the RS-485 converter is a DIP-switch. To configurate the RS-485

converter it is necessary to switch the DIP-block in the follow position:

•

Before the RS-485 converter can be used, a USB-driver must be installed at the PC.

Normally, this driver installed at a common PC. If it is not installed, the USB-Driver can

be download at the follow Web-Side:

http://www.visionsystems.de/produkte/usb-com-

plus-mini-usb-com-plus-mini-iso.html.

The download can be found under the topic

“Downloads”. The USB

driver is under the hyperlink “Current Windows x86 & x64”.

Without the USB-driver, the PC is not able to recognize the COM-port.

•

Connect the RS-485 converter via USB cable with a PC having installed MRU4Win

software.

Connect to USB-Pot

Содержание SWG100 CEM




























































































































































Результаты поиска

Содержание SWG100 CEM

Отзывы:

Похожие инструкции для SWG100 CEM

Бренды по названию

Популярные бренды

mru SWG100 CEM, Руководство пользователя

Результаты поиска

Содержание SWG100 CEM

Отзывы:

Похожие инструкции для SWG100 CEM

Бренды по названию

Популярные бренды