mru SWG100 CEM Скачать руководство пользователя страница 5

Страница: 5 / 155

SWG100 User Manual

MRU GmbH, D-74172 Neckarsulm

Inspect Shipment for Damage

Carefully inspect the entire shipment for damage in the presence of the shipper’s agent,

removing packaging material if necessary. Note any damage to packaging and/or goods on

Packing List and have it signed by the shipper’s agent prior to accepting the sh

ipment. Submit

damage claim to MRU immediately.
NOTE: Damage claims not received by MRU within 3 days of receipt of shipment will not be
accepted.

The products described in this manual are subject to continuous development and improvement

and it is therefore acknowledged that this manual may contain errors or omissions. MRU

encourages customer feedback and welcomes any comments or suggestions relating to the

product or documentation.
Please forward all comments or suggestions to the Customer Feedback Department at the
following address:

MRU GmbH

Fuchshalde 8 + 12

74172 Neckarsulm / Obereisesheim

GERMANY

Fon (+49) 71 32 99 62 0 (Reception)

Fon (+49) 71 32 99 62 61 (Service)

Fax (+49) 71 32 99 62 20

Email:

[email protected]

Homepage:

www.mru.eu

This manual is intended solely as a guide to the use of the product.
MRU shall not be liable for any loss or damage whatsoever arising from content errors or

misinterpretation of information’s from this manual or any mis

-use resulting from the use of this

manual.

FOR MORE INFORMATION ABOUT COMPANY MRU PLEASE VISIT OUR WEBSITE

www.mru.eu

Содержание SWG100 CEM




























































































































































Результаты поиска

Содержание SWG100 CEM

Отзывы:

Бренды по названию

Популярные бренды

mru SWG100 CEM, Руководство пользователя

Результаты поиска

Содержание SWG100 CEM

Отзывы:

Бренды по названию

Популярные бренды