mru SWG100 CEM Скачать руководство пользователя страница 105

Страница: 105 / 155

MRU GmbH

SWG 100 User Manual

Page

105

155

9.4.

Update the firmware

The analyzer and different installed options can be updated, if it is necessary. Following options

can be updated:

•

The firmware from the analyzer.

•

The firmware from the pcb- mainboard.

•

The firmware from the NDIR-bench.

•

The firmware from the installed I/O modules.

General steps for the firmware-update

Copy the actual firmware for the analyzer or the firmware from the option on a SD-

card. Be sure, that the firmware is in the mean root of the SD-card. All firmware

updates have the ending “fwb”.

Put the SD-card on the card slot on the operation unit. The card slot can be found

inside the door (see sketch below).

If the SD-card is recognized, the analyzer will make a noise.

Open the path:

XTRA

EVICE

NFO

. Dependent from the firmware update it can be

necessary to open the different submenus.

Update the analyzer (Firmware-

Updates with filename “1106.fwb”)

Open the path:

XTRA

EVICE

NFO

Press

F2 = details

to open the details for the main device menu.

BEEP!!

Содержание SWG100 CEM




























































































































































Результаты поиска

Содержание SWG100 CEM

Отзывы:

Бренды по названию

Популярные бренды

mru SWG100 CEM, Руководство пользователя

Результаты поиска

Содержание SWG100 CEM

Отзывы:

Бренды по названию

Популярные бренды