2 0 0 8 K n I G h t
109
2 0 0 8 K n I G h t
equIpment —
Sleeper to Sofa:
Remove all bedding from the hide-a-bed.
Grasp the foot of the hide-a-bed in the
center using the metal lifting bar.
Fold over the bottom portion of the bed
that will form the seat.
Lift the front portion of the lifting bar to
raise and lower the hide-a-bed back into
the sofa base.
Replace the seat cushions.
HIDe-a-BeD aIr mattreSS (optIonal)
The air mattress inflates and deflates in a
matter of seconds. Inflate the mattress by using
the electric inflation pump that operates from
any 120 Volt AC outlet. For ease of operation,
position the sofa so that accessing an electrical
outlet is convenient.
To Inflate Mattress:
Open sofa and allow the mattress to lie
flat.
Unzip the corner of the mattress labeled
“Air Pump Access”
Remove valve cap by turning cap
counterclockwise.
After cap is removed, insert pump
motor and turn clockwise until pump is
engaged.
Plug in pump motor and inflate to full,
approximately 60 seconds. A motor pitch
change occurs when mattress is full.
Remove pump and reseal valve cap by
turning clockwise.
Zip the “Air Pump Access” cover closed.
The bed is now ready for linen.
To Deflate Mattress:
Remove bed linen.
Unzip the corner cover of the mattress
labeled “Air Pump Access.”
Open deflation valve by lifting valve
latch. Allow mattress to deflate.
Once mattress is deflated swing valve
to closed position.
DO NOT LOCK
VALVE CLOSED
by locking the valve.
Air trapped in the mattress could cause
damage.
Zip the “Air Pump Access” cover closed
and close the sofa.
NOTE
DO NOT close deflation valve when
closing the sleeper mechanism.
WARNING
The electric inflation pump is for indoor
use only. DO NOT ues near or place in
water. Keep infants and small children
away from pump and product when not
fully inflated. Partially inflated product
can cause suffocation.
Removing the Mattress Valve:
Open deflation valve by lifting up on
valve tab.
Remove old valve by lifting the black
plastic on the outer edge of the valve
toward the center. The valve will then lift
out.
Installing New Mattress Valve:
To install the new valve, first open the
replacement.
Once open, seat the hinge area on to
the hinge support, then squeeze the
vinyl towards the center of the mattress
opening.
Feed the vinyl through the opening of the
new valve.
Once installed make sure there are no
bulges in the vinyl. Use thumb to make
sure that it is smooth.
Next, lock the replacement shut.
Select comfort aIr mattreSS
(optIonal)
The Air Mattress uses uniquely designed air
chambers to provide a gentle cushion of support
which can be adjusted for comfort and firmness.
The mattress can be personalized to an owner’s
ideal comfort level.
020260d
031117c
Air Mattress Remote
031117
Air Mattress Pump
Содержание 2008 Knight
