MKS 651D Series Скачать руководство пользователя страница 87

Страница: 87 / 162

Chapter Five: Remote RS-232 Operation

Setup Messages

How to Set the Pressure Units

The command [

value

] identifies the units for the 651 controller display, where:

value

: 00 = Torr (initial)

01  =  mTorr
02  =  mBar
03  =  µBar
04  =  kPa
05  =  Pa
06  =  cm H

07 = in H

To query the current pressure units, enter:

R 34

The controller responds with the message [

value

], where:

value

: 00 = Torr (initial)

01  =  mTorr
02  =  mBar
03  =  µBar
04  =  kPa
05  =  Pa
06  =  cm H

07 = in H

An example response, if the pressure units are Torr, is:

To change the units to mTorr, enter:

Note

The [

value

] command assigns a

label

to the pressure units; it does

not convert pressure readings. Pressure readings are reported as a
percentage (%) of full scale.

Содержание 651D Series



































































































































































Результаты поиска

Содержание 651D Series

Отзывы:

MKS 651D Series, Руководство пользователя, Страница: 87 / 162

Результаты поиска

Содержание 651D Series

Отзывы: