MKS 651D Series Скачать руководство пользователя страница 134

Страница: 134 / 162

Maintenance

Chapter Seven: Maintenance and Troubleshooting

122

7. Remove the Phillips head screw to the left of the Serial Interface connector.

8. Remove the CPU board from the 651 controller.

It may be necessary to remove the clamping spring that holds the card cage to the power
supply. If so, use needle-nose pliers or a screwdriver to pull the clamping spring
straight back and out.

9. Grasp each end of the board and rock it until it loosens from its position and lift the

board up and out of the unit.

How To Replace the RAM Module

1. Locate the battery-backed RAM module on the CPU board.

Refer to Figure 19.

Battery-Backed RAM Module (U3)

Figure 19: Location of the Battery-Backed RAM Module

2. Remove the RAM module from its socket using either needle-nose pliers, a screwdriver,

or an IC puller.

3. Position the new RAM module over the socket, being careful to line up the pins

correctly (pin 1 is located directly to the left of the notch).

4. Snap the module firmly into place on the CPU board.

Содержание 651D Series



































































































































































Результаты поиска

Содержание 651D Series

Отзывы:

MKS 651D Series, Руководство пользователя, Страница: 134 / 162

Результаты поиска

Содержание 651D Series

Отзывы: