MKS 651D Series Скачать руководство пользователя страница 56

Страница: 56 / 162

Setup

Chapter Four: Local Operation

Settings stored in non-volatile RAM are saved when the power is turned
off. When the power is restored, the 651 unit “remembers” the latest
configuration, not the initial configuration.

To enter the Setup Menu to configure the operating parameters:

1. Press the [

] and [

] keys simultaneously for about three seconds.

The screen displays:

CONTROL

MODE PID

Select the desired pressure control mode, PID.

2. Press the [

] key to advance to the next screen.

The screen displays:

BAUD RATE: 9600

Select the baud rate from the options of 300, 1200, 2400, 4800, 9600 (initial), and 19200.

3. Press the [

] key to advance to the next screen.

The screen displays:

PARITY: NONE

Select the parity from the options of NONE (no parity / 8 data bits - initial) or EVEN
(even parity / 7 data bits).

Содержание 651D Series



































































































































































Результаты поиска

Содержание 651D Series

Отзывы:

MKS 651D Series, Руководство пользователя, Страница: 56 / 162

Результаты поиска

Содержание 651D Series

Отзывы: