MKS 651D Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 162

MKS 651D Series Скачать руководство пользователя страница 29

Chapter Two: Installation

Setup

17

Grounding

For protective earthing, plug the power cord into a properly grounded outlet.

How To Set the Line Voltage

The line voltage selector, located on the rear panel of the 651 unit (refer to Figure 9), configures
the 651 unit to accept either 115 or 230 VAC input voltage

Caution

The Line Voltage Selector on the 651 unit must be set to the proper
input voltage

before

you connect the power cord and turn on the

power. Otherwise, the unit will be severely damaged.

Note

Be sure to install the correct fuses for the line voltage selected.

To change the line voltage:

1. Be sure that the power cord and all interface cables are disconnected from the 651

controller.

2. Use a blunt instrument, such as a flat head screwdriver, to slide the line voltage selector

switch to the left position for operation in the 115 V range, or to the right position for
operation in the 230 V range.

Refer to Figure 3. The value of the selected line voltage is visible through the window
in the cover of the switch. The voltage and fuse label above the switch shows the
corresponding voltage range and fuse requirements for either voltage setting.

Line Voltage
Selector Switch

Selected Voltage

Voltage and Fuse
Label

Figure 3: Line Voltage Selector

«
...
27
28
29
30
31
...
»

Содержание 651D Series



































































































































































Отзывы:

Нет отзывов