MKS 651D Series Скачать руководство пользователя страница 143

Страница: 143 / 162

Appendix A: Product Specifications

131

Appendix A: Product Specifications

Ambient Operating Temperature Range

to 40

C (59

to 104

to 35

C (59

to 95

F) with the optional

valve failsafe battery backup

Analog Output Signal

Position
Pressure

0 to 5 Volts or 0 to 10 Volts, selectable
110% FS pressure, same range as sensor

CE Mark Compliance

Electromagnetic Compatibility

Low-Voltage Requirements

Installation Category

Pollution Degree

Product Safety Requirements

Pending

EMC Directive 89/336/EEC

Low-Voltage Directive 73/23/EEC

II, according to EN 61010-1

2, according to IEC 664

Product Safety Directive 92/59/EEC

Connectors

RS-232 Serial Communications
Interface
Transducers
Valve

9-pin Type “D” male
37-pin Type “D” female
15-pin Type “D” female (Stand. & Hi-Dens.)
9-pin Type “D” female

Controller Repeatability

±0.1% of FS

Digital Interface

Inputs (16): HCMOS pulled high with a 4.7k
resistor to be TTL compatible. Driver must
sink 1 mA and hold low for > 50 msec to
select function.

Outputs (6):HCMOS with 240 ohm series
protection resistor. Will sink & source 1 TTL
load. Time constant < 500 nanoseconds.

Dimensions

With optional valve failsafe battery
back-up

3½” H x 9½” W x 9” D
(8.9 cm x 24.1 cm x 22.9 cm)

12”D (30.5 cm)

Display

2 line LCD with 4½ place readout

An overall metal braided shielded cable, properly grounded at both ends, is required during use.

Interconnecting cables between the 651 controller and the valve, sensor, and serial communications are

available at an additional charge. Please consult factory for ordering information.

Содержание 651D Series



































































































































































Результаты поиска

Содержание 651D Series

Отзывы:

MKS 651D Series, Руководство пользователя, Страница: 143 / 162

Результаты поиска

Содержание 651D Series

Отзывы: