MKS 651D Series Скачать руководство пользователя страница 22

Страница: 22 / 162

Product Location and Requirements

Chapter Two: Installation

Optional Equipment

•

Electrical Connector Accessory Kit - 651D-K1

Includes an I/O connector for the rear panel of the unit, a cover for the I/O

connector, and a screwlock assembly for the I/O connector cover

•

MKS Type 253 (fast or standard) or 653 control valve

•

Valve Failsafe Battery Back-Up (factory installed)

•

Rack Mounts:

RM-13 (supports a 9” deep rack - for a standard 651 unit)

RM-14 (supports a 12” deep rack - required for mounting a unit with the

valve failsafe battery back-up)

•

System Interface Cables (Table 3)

•

Adapter Cables (Table 4)

Product Location and Requirements

The Type 651 unit meets the following criteria:

•

POLLUTION DEGREE 2 in accordance with IEC 664

•

Transient overvoltages according to INSTALLATION CATEGORY II

Operating Environmental Requirements

•

Ambient Operating Temperature: 15

to 40

C (59

to 104

to 35

C (59

to 95

F) with the optional valve

failsafe battery back-up

•

Main supply voltage fluctuations must not exceed

10% of the nominal voltage

•

Ventilation requirements include sufficient air circulation

•

Connect the power cord into a grounded outlet

Safety Conditions

The 651 controller poses no safety risk under the following environmental conditions.

•

Altitude: up to 2000 m

•

Maximum relative humidity: 80% for temperatures up to 31

C, decreasing linearly to

50% at 40

Содержание 651D Series



































































































































































Результаты поиска

Содержание 651D Series

Отзывы:

MKS 651D Series, Руководство пользователя, Страница: 22 / 162

Результаты поиска

Содержание 651D Series

Отзывы: