MKS 651D Series Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 162

MKS 651D Series Скачать руководство пользователя страница 129

Chapter Six: Remote Digital Logic Control

How To Activate the Softstart Rate

117

How To Activate the Softstart Rate

When using the front panel controls or RS-232 to Open the valve, Close the valve, or use a
setpoint, the softstart rate is automatically activated. Having a softstart rate setting of 100% is the
same as not applying any softstart rate.

The following section applies to the use of TTL commands to Open the valve, Close the valve,
or use a setpoint.

The softstart rate for the active set point is controlled by the state of digital logic input pin 7 on
the Interface connector. This line must be held low to activate the softstart rate.

To activate softstart control of the active set point:

1. Hold the softstart line low (pin 7 on the Interface connector).

Refer to Table 8, for the Interface connector pinout. Hold the TTL low signal for a
minimum of 50 milliseconds. If the line is

not

held low, the valve will move at 100%

full speed.

«
...
127
128
129
130
131
...
»

Содержание 651D Series



































































































































































Отзывы:

Нет отзывов