MKS 651D Series Скачать руководство пользователя страница 136

Страница: 136 / 162

Maintenance

Chapter Seven: Maintenance and Troubleshooting

124

How To Replace the Optional Valve Failsafe Battery

Warning

The 651 unit has lethal voltages inside. Only qualified
personnel must perform servicing of the unit.

To avoid an electrical shock, disconnect the power line before
opening the unit.

1. Turn the power off.

2. Disconnect the AC power cord.

Caution

To avoid damage to sensitive internal components, personnel should
be grounded through a safety impedance while working inside the
651 unit, and the unit itself must be static-free.

3. Remove the three Phillips screws located at the top of the rear panel and the one on the

side.

4. Disengage the cover from the rear chassis by lifting it up from the clips.

5. Remove the top cover by firmly pulling it up and back to clear the top of the connector

plates.

6. Locate the area of the unit where the chassis splits (to the rear of the front panel) and

remove the two screws on both sides of the front panel as well as the two screws on
both sides of the battery backup housing.

7. Slide the front panel out far enough to enable the ribbon cable to lay flat.

8. Slide the battery backup housing out about an inch.

9. Disconnect the battery power bus interface from the battery backup circuit board.

10. Unsnap the ribbon cable connector.

11. Pull both the front panel module and the battery backup housing away from the card

cage/power assembly.

12. Remove the screw located on the left side of the housing.

13. Orient the housing on its side, and remove the two visible screws.

Содержание 651D Series



































































































































































Результаты поиска

Содержание 651D Series

Отзывы:

MKS 651D Series, Руководство пользователя, Страница: 136 / 162

Результаты поиска

Содержание 651D Series

Отзывы: