Mitsubishi FX3UC Series Скачать руководство пользователя страница 218 | Manualshive

Страница: 218 / 458

background image

212

FX

3UC

Series Programmable Controllers

User’s Manual - Hardware Edition

8 Terminal Block Specifications and External Wiring

INSTALLATION PRECAUTIONS

• Use the product within the generic environment specifications described in Section 3.1 of this manual.

Never use the product in areas with excessive dust, oily smoke, conductive dusts, corrosive gas (salt air, Cl

2

, H

2

S,

SO

2

or NO

2

), flammable gas, vibration or impacts, or exposed to high temperature, condensation, or rain and

wind.
If the product is used in such conditions, electric shock, fire, malfunctions, deterioration or damage may occur.

• Do not touch the conductive parts of the product directly.

Doing so may cause device failures or malfunctions.

• Install the product securely using a DIN rail or mounting screws.

• Install the product on a flat surface.

If the mounting surface is rough, undue force will be applied to the PC board, thereby causing nonconformities.

• Make sure to affix the expansion board with tapping screws.

Tightening torque: 0.3 to 0.6 N

•

m

Loose connections may cause malfunctions.

• When drilling screw holes or wiring, make sure that cutting and wiring debris do not enter the ventilation slits.

Failure to do so may cause fire, equipment failures or malfunctions

• Be sure to remove the dust proof sheet from the PLC's ventilation port when installation work is completed.

Failure to do so may cause fire, equipment failures or malfunctions

• Connect the extension cables, peripheral device cables, input/output cables and battery connecting cable

securely to their designated connectors.
Loose connections may cause malfunctions.

• Connect the display module, memory cassette, FX

2NC

Series I/O extension blocks, FX

2NC

-CNV-IF, extension

power supply unit and expansion board securely to their designated connectors.
Loose connections may cause malfunctions.

• Turn off the power before attaching or detaching the following devices.

Failure to do so may cause device failures or malfunctions.
- Peripheral devices, display module, expansion boards and special adapters
- Extension blocks, FX Series terminal blocks, Connector conversion adapter and extension power supply unit
- Battery and memory cassette

Note

• When a dust proof sheet is supplied with an extension unit/ block, keep the sheet applied to the ventilation slits

during installation and wiring work.

Main unit, FX

2NC

Series I/O extension blocks, FX

2NC

/FX

3UC

Series

special function blocks, special adapter, extension power supply unit,
FX

2NC

-CNV-IF, FX

2N

-10GM, FX

2N

-20GM, FX Series terminal blocks

DIN rail only

FX

0N

/FX

2N

Series I/O extension blocks, FX

0N

/FX

2N

/FX

3U

Series special

function blocks, FX

2N

-1RM(-E)

DIN rail or direct
mounting

«
...
216
217
218
219
220
...
»

Содержание FX3UC Series











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FX3UC Series

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: Samsung Страницы: 27

Бренд: Baccara Страницы: 16

Бренд: BABYSTYLE Страницы: 8

Бренд: BABYSTYLE Страницы: 32

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды