Mitel Inter-Tel Axxess Скачать руководство пользователя страница 280 | Manualshive

Страница: 280 / 384

Mitel Inter-Tel Axxess Скачать руководство пользователя страница 280

Page 264

System Features

Inter-Tel

®

Axxess

®

Administrator Guide — Issue 11.0, May 2008

Paging

PAGING

The Paging feature allows announcements to be made through endpoint internal speakers.
Optional external paging equipment (amplifiers and paging speakers) may also be installed.

There can be up to 10 paging zones (50 when using a CP Server). When the system is in the
default state, all Inter-Tel endpoints are assigned to paging zone 1 to provide an all-page zone.
Inter-Tel endpoints, trunks, and the external paging port(s) can be assigned to any, all, or none
of the paging zones, as desired.

NOTE:

Placing a large number of Inter-Tel endpoints in a paging zone may affect system per-

formance. If system operation is affected when a page is placed to a particular page zone,
remove some Inter-Tel endpoints from that zone or change to external paging for the area
served by that page zone.

In a network, all Inter-Tel endpoints and trunks within a page zone must reside on the same
node as the page zone. However, a page zone can contain external page ports on other nodes.

NOTE:

Because the external paging ports have intercom numbers (91000 and 91001), sta-

tions can place an intercom call to the external paging ports, instead of using the Page feature,
to make a page over the external paging speakers.

Pages are not heard on Inter-Tel endpoints that have been removed from paging (using the fea-
ture code as described below), are in Do-Not-Disturb, are ringing, or are in use. Also, back-
ground music on endpoints and on external speakers connected to endpoint speaker leads is
interrupted for pages. If a trunk in a paging zone is unplugged, the page cannot be completed.

If desired, Inter-Tel endpoint users can program feature buttons to select the paging zones 0-9
(or 0-49) using paging access codes 9600-9609 (or 9600-9649).

The Page timer limits the length of pages. If it is set to 0, pages are unlimited in length.

To make a page:

1.

Lift the handset.

2.

Inter-Tel endpoints—

Press the PAGE button, or enter the Page feature code (7). The

display shows SELECT PAGE ZONE # (0-9).

Single-Line Sets—

Enter the Page feature code (7).

3.

Enter the zone code (0-9 or 0-49) for the desired zone.

4.

After the single progress tone, make your page before the Page timer expires. If you
hear reorder tones, and the display shows PAGE ZONE NOT PROGRAMMED, there
are no stations in the selected page zone. If the display shows PAGE ZONE BUSY
TRY AGAIN LATER, the necessary system resources are busy or the paging zone is
being used by another station. Users cannot camp on to or queue the paging system.

5.

Hang up.

«
...
278
279
280
281
282
...
»

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды