manualshive.com logo in svg

Mitel Inter-Tel Axxess, Руководство администратора

Поделиться
Скачать
Mitel Inter-Tel Axxess Скачать руководство пользователя страница 169

Page  153

Trunk Features

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0,

 

May 2008

TRUNK FEATURES

This section explains the trunk functions and programmable features.

CALLER ID, DNIS, AND ANI

NOTE:  

The Advanced CO Interfaces premium feature license is required to use the following

features.

The system supports Caller ID, ANI, and DNIS to data about the source of the call. 

•

Caller ID: 

Caller ID information gives the caller’s telephone number and/or name.

•

Automatic Numbering Identification (ANI): 

ANI information identifies the caller’s

telephone number. The system receives a specified number of digits.

•

*ANI*: 

This is a form of ANI that does not have a specified number of digits. The sys-

tem receives a star (*) before the ANI digits to signal the beginning of the caller’s tele-
phone number. Then there is another star after the digits to signal the end of the ANI
information.

•

Dialed Number Identification Service (DNIS): 

DNIS identifies the number that was

dialed to reach your location. The system receives a base number and a specified num-
ber of digits that identify the dialed number.

•

*DNIS*: 

This is a form of DNIS that does not have a specified number of digits. The

system receives a star (*) before the DNIS digits to signal the beginning of the dialed
number. Then there is another star after the digits to signal the end of the DNIS infor-
mation.

•

*ANI*DNIS*: 

This is a two-stage address service that provides both the caller’s tele-

phone number and the dialed number. It combines the *ANI* and the *DNIS* features
described above.

CAUTION

While this system is designed to be reasonably secure against CO trunk misuse by outside
callers, there is no implied warranty that it is not vulnerable to unauthorized intrusions and
toll fraud. If the central office does not provide supervision it will not disconnect the call when
one party hangs up; it is possible for a caller to remain connected to a CO trunk circuit. If
this happens, and the caller begins dialing, the call could be placed through the system and
would then be billed to the system’s owner. The system cannot check this type of call for toll
restriction and may not register the call in SMDR. This problem could arise when a call is
connected to a station or when a call is in an unsupervised conference.

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды