Mitel Inter-Tel Axxess Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 384

Mitel Inter-Tel Axxess Скачать руководство пользователя страница 216

Page 200

System Features

Inter-Tel

®

Axxess

®

Administrator Guide — Issue 11.0, May 2008

Off-Hook Voice Announce (OHVA)

To place an off-hook voice announce call:

1.

When placing an intercom
call to a busy OHVA-enabled
Inter-Tel endpoint, do not
hang up. You hear busy sig-
nals until the Camp-On and
O H VA   S c r e e n i n g   t i m e r s
expire. (If you hear music
a f t e r   t h e   C a m p - O n   t i m e r
expires, conditions for an
OHVA call were not met and
y o u   a r e   c a m p e d - o n .   S e e

.)

2.

When the OHVA Screening timer expires (and if the endpoint’s secondary voice path is
available), you are automatically connected to the called party’s speakerphone.

To place an immediate off-hook voice announce call (Inter-Tel endpoints with DSS/BLF
buttons only):

NOTE:

This method can only be used if the database has been programmed to allow Inter-Tel

endpoints with DSS/BLF buttons to bypass the Camp-On and OHVA Screening timers.

1.

When an intercom call is placed, using a DSS/BLF button, to a busy OHVA-enabled
Inter-Tel endpoint, do not hang up.

2.

Press the DSS/BLF button for that endpoint again. If the endpoint’s secondary voice
path is available, you are immediately connected and may speak.

To receive an off-hook voice announce call (OHVA-enabled Inter-Tel endpoints only):

1.

While on a call using the handset, you hear a camp-on tone. The display shows CALL
ANNOUNCE FROM

(username

). Do nothing. When the OHVA Screening timer

expires, you hear a double tone. You are connected with the intercom caller via the
speakerphone. Your original call remains connected on the handset.

NOTE:

If you press

while speaking to the caller on the speakerphone, the

handset microphone will be muted and the caller on the handset will not hear you or the

OHVA caller. Press

again to enable the handset.

2.

To terminate the OHVA call:

Press the lit Speaker button or have the OHVA caller

hang up.

If you terminate the original call by hanging up the handset, you remain con-

nected to the OHVA call in the handsfree intercom mode.

To block an off-hook voice announce call (OHVA-enabled Inter-Tel endpoints only):

1.

While on a call using the handset, you hear a camp-on tone. The display shows CALL
ANNOUNCE FROM

(username

). To cause the intercom call to camp on, press the

Speaker button. The

button flashes.

2.

If you want to send Do-Not-Disturb signals to the camped-on call,

press the

button.

OFF-HOOK VOICE ANNOUNCE

ENDPOINT WITH

PCDPM

Ext. 1103

Ext. 1002

ACTIVE

CALL ON

HANDSET

Caller places a call
to ext. 1002 and
hears busy signal

Display shows INTERCOM

CALL FROM 1103

After 5 seconds, call is

established on speaker, if not

blocked.

1

2

3

MUTE

MUTE

IC

DND

«
...
214
215
216
217
218
...
»

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды