MINOS T-MDR 1000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 9

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

This first information

is no substitute for present instructions for use.

Present instructions for use, informs you most detailed about every single
action which must be taken, from first start of the machine itself, proper and
safe use, over to the maintenance.

Instructions are divided in single chapters with text and illustrations, explaning
practical course of every single step during use of machine. Due to upper facts
please read carefully these instructions, before you start using the machine and
take into consideration all security regulations.

Important!
To avoid accidents and for acheiving optimal working – capacities of the
machine, any kind of tecnical changes without strict concordance from the
side of producer is strictly forbidden. In such a manner also the machine must
be used exsclusively according to from MINOS prescribed conditions.

●  The  Safety  Alert  Symbol  used
throughout  this  manual  and  on
safety  decals  of  the  machine
indicates

the

presence

of

potential  hazard  to  the  operator.
When  you  see  this  symbol,  be
alert  and  carefully  read  the
message that follows it.

● This symbol is to be found on
different spots in these informations,
showing

at

special

procedure

informations which must be specially
considered during the use of machine.

● Before starting the machine, read carefully this instructions for use,
maintenance and safety instructions.

● This instructions booklet is part of the machine itself and must always
with the machine. Also in the case that machine is sold to another owner.

1- INSTRUCTIONS FOR SAFE WORK

1

«
...
7
8
9
10
11
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов