MINOS T-MDR 1000 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 28

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

3.1.2- Tractor PTO Horsepower Requirements:

Required tractor power may vary depending on the ground conditions, soil
structure, desired speed to tillage, the intended rotating speed of the rotor and
working depth.

Model ID

Required tractor
power (HP)

Model ID

Required tractor
power (HP)

T-MDR 1000

35 (26.1 kW)

T-MDR 1000

60 (44.74 kW)

T-MDR 1250

40 (29.8 kW)

T-MDR 1250

75 (55.93 kW)

T-MDR 1500

50 (37.28 kW)

T-MDR 1500

85 (63.38 kW)

Table 6- Recommended tractor power

* 1 HP = 0,745 kW

3.1.3- Tractor Electricity Requirements:

The  transit-mode  lightening  system  is  recommended  as  an  option  and  needs
tractor  electricity.  If  the  mini  power  harrow  will  be  transported  on  a  public
roadway, be sure the lights are in good working order.

Electric connection must match the following scheme of the socket.

Figure 6/ Table 7- Required electrical connection

(12V socket for lighting equipment)

● Electric connector covers should be in place to keep out dust, dirt, grease,
and moisture. Clean connections keep systems working without delays.

Type

Wire colour

1/L

Blue

2/54G

-

3/31

Black

4/R

Green

5/58R

-

6/54

Brown

7/58L

Yellow

20

«
...
26
27
28
29
30
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов