manualshive.com logo in svg

MINOS T-MDR 1000, Руководство по эксплуатации, Страница: 27 / 87

Поделиться
Скачать
MINOS T-MDR 1000 Скачать руководство пользователя страница 27

© Copyright

 MINOS DIS TICARET LIMITED SIRKETI., 2020. All  rights reserved. Reprinting, even of sections, only possible with the approval of

 

MINOS DIS TICARET LIMITED SIRKETI.

                                                        Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020 

 

 
 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

The  machine  is  designed  to  be  mounted  on  Category  2,  medium-high  power 
tractors  (ISO  730  standard)  equipped  with  hydraulic  lift  and  universal  three-
point hitch that can support the machine weight and is driven by tail spindle of 
the tractor through the PTO Shaft. (Nominal rev. speed max. 540 

   

  

.) 

 
The  tractors  used  to  operate  the  machines  must  have  the  following 
requirements: 

 
 

3.1.1- Tractor Weight Requirements: 

 

 

M = Machine wt 

T = Tractor wt. + Ort. 75 kg operator 

Mini power harrow with rear roller  

M ≤ 0,3T 

Table 5- Calculating required tractor weight 

 

* 1 kg = 2,20 pound (lbs) 
 
 

 

●  READ  ALL  WARNINGS  AND  INSTRUCTIONS  IN  THIS  MANUAL  BEFORE 
PREPARING  OR  OPERATING  THE  MINOS  MINI  POWER  HARROW!

 

It  is  the 

responsibility  of  the  owner  to  make  sure  the  machine  is  set  up  properly. 
The following recommendations should be helpful.

 

 

●  Directional  indications  such  as  'left',  'right',  'front'  and  'rear'  are  to  be 
interpreted when facing in direction of travel, with the machine attached to 
the rear of the tractor. 

 

3.1- Tractor Requirements

 

 

3- PREPARING FOR OPERATION 

19 

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов