MINOS T-MDR 1000 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 4

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

This warranty provided by MINOS DIS TICARET LTD. STI. does not cover any faults caused by
any abnormal or unintended use of the meter.

We declare:

●  that  during  the  warranty  period,  the  product  will  operate  flawlessly,  if  you  use  it  in
accordance with its purpose and the enclosed instructions;
●  that  upon  your  request,  we  will  repair  any  defect  of  the  machine  if  you  inform  us  of  it
during  the  warranty  period.  The  warranty  takes  effect  from  the  date  of  purchase  of  the
product, evident from the certified warranty certificate and the receipt.
●  The  machine  is  is  specifically  designed  for  agricultural  application  and  is  intended  to  be
used to tillage the soil and prepare the seedbed.

The warranty becomes invalid due to:

● failure to comply with the enclosed instructions;
● damage and faults caused by improper use;
● usage of an unsuitable PTO shaft;
● negligent handling of the product, overloading which leads to the fracture of any parts;
● interference with the product by an unauthorised person;
● damage caused by mechanical shock due to the fault of the buyer or a third person;
● damage caused by flooding, fire, lightning;
● damage and faults caused during transport, shipment, loading and unloading;
●  damage  and  faults  caused  by  fire,  lightning,  flood  and  earthquake  (natural  disasters),
inappropriate environment and accidents;
●  faults  caused  by  installation  or  connection  of  the  meter  not  in  compliance  with  the
installation and operating manual;

The  warranty will  be  valid  only for the period  stated on the  reverse  side  of this  certificate
and the faults at the product, and no other right or damages under any reason whatsoever
can be claimed. In the events that the warranty certificate is destroyed or defaced, that the
serial number on the product is removed or destroyed, the warranty certificate will become
null and void. Any warranty certificate not bearing the seal and authorised signature of the
seller and the date of sale will not be valid.

MINOS is liable for damages it caused by intentional and deliberate damages, not for minor
negligence. Besides, it will not be liable for the results, including but not limited to the
interruption of business activities or loss from profit due to this reason, or any loss caused as
a result of the failure of a duty due to the breakdown of the product.

If there is any defect in the product, the defective product shall be sent to MINOS with risks
and expenses on customer’s account. The defects of the product will be removed by MINOS
by replacing a new one or repairing the same.

CAUTIONS ABOUT THE WARRANTY

«
...
2
3
4
5
6
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов