MINOS T-MDR 1000 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 10

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

The  machine  is  is  specifically  designed  for  agricultural  application  and  is
intended to be used to tillage the soil and prepare the seedbed. If the machine
is used for any other purpose, and get damaged during this, the manufacturer
is not liable for the damage caused to the machine. It is the user himself who
bears the risk.

All  conditions  for  work  and  maintenance,  prescribed  by  the  manufacturer,
should strictly be considered.

The  machine  may  only  be  used,  handled  and  repaired  by  persons  who  are
appointed to do this and who are familiar with the instructions for safe work,
with settings and with maintenance of the machine.

All  relevant  safety  regulations  as  well  as  all  generally  used  safety  tehnical,
working-medical and traffic regulations should be considered during the work
with the machine.

When the mini power harrow is in operation it has many moving parts which
could cause severe injury or death to persons coming in contact with these
parts. To help avoid serious accidents, the following guidelines should always
be followed:

●

Be sure all safety guards are in place before operating, including tractor PTO

driveline covers.

1.1- Regular Use In Agriculture

● The manufacturer is not liable for damages, caused to the machine which
has been rebuilt by the user, if damages had occured as a result of the
rebuilding.

1.2- Accident Prevention and Safety Instructions

2

«
...
8
9
10
11
12
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов