MINOS T-MDR 1000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 35

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

Before the start up and before reusing the machine after a long

term storage (e.g. after seasonal end), perform the following pre-operational
inspections and service of the machine, to assure that the machine is in
perfect condition and ready to be used:

● Make sure you have read and understood the Introducing &

operating

manuals of the machine, tractor and PTO shaft, and followed what is described
in the section 3.

● Before the start up the machine, the operator must always use appropriate
Personal Protective Equipment (PPE).

3.4- Before The Power Harrow Run-in

27

26

● BEFORE fitting or disfitting PTO shaft: Tractor and machine on a flat
surface, with parking brake set, engine off, and ignition key removed!

● Always pay your best attention to proper mounting and securing of the
P.T.O. Shaft!

● Cleaning, lubrication or adjusting of the PTO shaft can be done when the
engine is switched off and the ignition key is pulled out!

● Repair all damages of the PTO shaft before fitting!

●

BEFORE OPERATING THE MACHINE, ENSURE THAT THE SIZE OF THE PTO

SHAFT BETWEEN TAIL SPINDLE OF THE TRACTOR AND THE INPUT SHAFT OF
THE MACHINE IS ADEQUATE.

«
...
33
34
35
36
37
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов