MINOS T-MDR 1000 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 65

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

The mini power harrow is equipped with a rear roller and specifically designed
for  agricultural  application  and  must  be  used  for  mechanical  soil  tillage  and
seed-bed  preparation  on  farms,  in  vineyards  and  orchards,  as  well  as for row
crops and speciality crops.

It is a simple and reliable system that requires minimal maintenance.

The  following  section  lists  common  problems,  causes,  and  solutions  to  the
problems  you  may  encounter  with  your  power  harrow.  Should  any
maintenance  and  service  be  required  as  a  result  of  troubleshooting,  refer  to
the

section 6

for assistance.

If you encounter a problem that is difficult to solve, even after having read
through this troubleshooting section, please call your dealer or distributor.
Before you call, please have this introducing & operating manual and the serial
number of your machine

(See section 9 and fig. 26).

PROBLEM

POSSIBLE CAUSE

POSSIBLE SOLUTION

Noise from PTO
shaft during
machine lifting

● Bad connection
between machine and
tractor
● Machine is lifted too
much

● Adjust the tractor top link
● Limit the lifting

Noise noticeable
and constant from
gearbox/gears
transmission trough

● Low oil level
● Worn gears

● Add oil
● Replace gears

Intermittent noise
from the machine

● Loose blades
● Gear tooth damaged

● Tighten blades hardware
● Replace damaged gear

Driveline vibration

● Worn PTO Shaft
● Machine lifted too
high
● Debris wrapped
around blades and/or
rotors

● Replace PTO Shaft
● Lower machine and read just
tractor top link
● Remove debris

8- TROUBLESHOOTING

57

«
...
63
64
65
66
67
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов