MINOS T-MDR 1000 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 87

MINOS T-MDR 1000 Скачать руководство пользователя страница 12

© Copyright

MINOS DIS TICARET LIMITED SIRKETI., 2020. All rights reserved. Reprinting, even of sections, only possible with the approval of

MINOS DIS TICARET LIMITED SIRKETI.

Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020

●  Safety  and  warning  decals,  placed  on  the  machine,  give  important
instructions for safe work. Take them into consideration for your safety!

●  Make  sure  you  get  familiar  with  all  devices  and  elements  for  handling  and
with the functions, before starting with the work!

● To avoid danger of fire, keep the machine clean!

● Before switching on the machine and  driving off, make sure there is  noone
near the machine (children). Make sure your visibility is sufficient!

● It is prohibited to drive persons on the machine!

● It is prohibited to be in the working and dangerous area of the machine!

● Stay away from the area of swinging and turning of the machine!

● Pay special attention while cleaning the power harrow. The machine must be
switched off, PTO Shaft must be disconnected from the machine. It is forbidden
to step on the machine while it is connected to the tractor; there is danger of
being pulled between the blades rotors.

● PTO Shaft, tillage unit etc. May be put in  action only when no one is in the
swinging area!

● On all parts of the machine, which are mecanically driven, there is danger of
shear and squeeze!

●  Secure  the  machine  before  leaving  the  tractor.  Lower  the  machine
completely.

● Switch off the engine and pull out the ignition key!

●  Stop  operating  immediately  if  blades  strike  a  foreign  object.  Repair  all
damage and make certain that rotor and blades are in good condition before
resuming operation.

4

«
...
10
11
12
13
14
...
»

Содержание T-MDR 1000
























































































Отзывы:

Нет отзывов