MIMAKI TEXTILE JET TX1800B, Руководство по эксплуатации

Страница: 177 / 222

5-11
1
2
3
4
5
T
roubleshooting
Warning/Error Messages
If some trouble occurs, the buzzer sounds and the display shows a corresponding error message.
Take appropriate measures to remedy the displayed error.
Warning Messages
• If there are multiple troubles, [ ! ] in the display will be inverted to
inform you of it. Press the key to check the contents of
troubles.
Message Cause Solution
The pressure in the ink tank is
likely to exceed the proper range. Perform the negative pressure adjustment.
(
P.4-46)
The pressure in the ink tank
exceeds the proper range.
Perform the negative pressure adjustment.
(
P.4-46)
Ink was not absorbed because there
are dirt in the vicinity of the head
and the ink cap.
Perform cleaning of the capping station and the
nozzle surface. (
P.4-10)
Time to clean the wiper has come. Execute the wiper cleaning. ( P.4-5)
Time to replace the wiper with a new
one has come.
Replace the wiper with a new one. ( P.4-6)
The maintenance cover is open. Close the maintenance cover.
The head height is not proper. Or,
the fabric is floating (the head
protection sensor detected an error.)
Check the head height or the status of the fabric
you set.
The clamp lever is in the upper
status.
Push down the clamp lever.
The environmental temperature is
outside the temperature range for
printing.
(Temperature range : 15

C to 30

C
59

F to 86

F)
Adjust the temperature of the installation
environment so that it is within the range of 15

C
(59

F) to 30

C (86

F).
The environmental temperature is
below the operable temperature
(4

C (39

F)).
Adjust the temperature of the installation
environment so that it is 4

C (39

F) and higher.
The battery is dead.
Contact our service office or the distributor in your
region.
Ink for cleaning or ink initial filling is
not enough. Replace the ink pack corresponding to the
displayed color number.
Motor excitation has been cut off.
(1) Close the cover and move the clamp lever
down.
(2) Press the key to perform the initial
operation.
The media width has not been
detected.
Perform the media detection.
A smaller size media than the data
to be printed has been set.
Set an enough size media for printing.
The time to replace the X motor.
Contact our service office or the distributor in your
region.
E r r o r I n f o
D i s p l a y [ V ] K e y
! P r e s s u r e A d j .
! W r o n g P r e s s u r e
! S u c t i o n
1 2 3 4 5 6 7 8
! W i p e r
C l e a n W i p e r
! W i p e r
R e p l a c e W i p e r
! M a i n t e . C o v e r
C l o s e T h e C o v e r
! H e a d H e i g h t
C h e c k H e a d H e i g h
! L e v e r
C h e c k T h e L e v e r
! T e m p e r a t u r e
E n v . T e m p i s L o w
! T e m p e r a t u r e
E n v . T e m p i s H i g h
! B e l o w O p e r a b l e
T e m p e r a t u r e
! R e p l a c e B a t t e r y
! I n k L o w
1 2 3 4 5 6 7 8
! O p e r a t i o n
M o t o r O F F
! O p e r a t i o n
M e d i a U n - D e t e c t i o n
! O p e r a t i o n
P r i n t A r e a S h o r t
! X M o t o r
R e p l a c e X M o t o r