Milnor Emerald EX-15 Скачать руководство пользователя страница 74

Страница: 74 / 87

Trouble shooting

Turn the machine’s wall switch off and on again.
Start a program.

Error code returns

No error code

Check wiring from X75 on program control unit
PCB to X301 on motor control unit. Use an
ohmmeter to check that the four conductors are
sound as follows:

X75:

X301:

Measure also between the four connections in
X75 to eliminate possibility of short-circuits
between two conductors.

Wiring sound

Wiring faulty

Check input voltage (120/230 V) to the motor
control unit on contact X 311 (measure on rear
of PCB).

Wrong voltage

Voltage correct

Replace motor control
unit.

Malfunction Function
remains

normal

Check voltage (120/230 V) across fuses F21 -
F22.

Wrong voltage

Voltage correct

13E

Program control unit receiving
no response from the motor
control unit.

Error codes which may arise on the control panel display

X75

X311

2316 3333

F22 F21

3332

Error code/symptoms

Fault-finding

X301

Check wiring and replace if
necessary.

Transient fault. No action
required.

Cause/Action

Coil L1 faulty. Replace coil.

Input voltage to machine
incorrect.

Fault in motor control unit
communications circuits.

Probable fault in program
control unit PCB
communications circuits. Refit
the original motor control unit
and replace the program
control unit PCB.

Содержание Emerald EX-15
























































































Результаты поиска

Содержание Emerald EX-15

Отзывы:

Milnor Emerald EX-15, Руководство по эксплуатации и техническому обслуживанию, Страница: 74 / 87

Результаты поиска

Содержание Emerald EX-15

Отзывы: