Milnor Emerald EX-15 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 87

Milnor Emerald EX-15 Скачать руководство пользователя страница 60

56

Service program

Simulation of functions

Some machine functions can be simulated by entering a numerical code
via the keys. This function can then be switched on and off with the ON/
OFF key.

Number Code

Function

11

Detergent signal 1, liquid detergent.

12

Detergent compartment 2, cold water /Detergent signal
2, liquid detergent.

13

Detergent compartment 3, cold water /Detergent signal
3, liquid detergent.

14

Detergent compartment 2, hot water /Detergent signal
4, liquid detergent.

15

Detergent signal 5, liquid detergent.

16

Hot water in drum.

17

Detergent compartment 1, cold water.

18

Hard water in drum.

19

Heat: display shows actual temperature in drum, not
code 19. When ”START” is pressed, the heating relay
reacts if the water level is above 64 scale units. (Safety
level).

21

Drain valve/pump

23

Activate door lock. When it is deactivated, the water
drain valve will also open.

24

Level check. The parameter corresponding to the
actual level will be shown on the display, not code 24.
When ”START” is pressed, filling with cold water
commences via detergent compartment 1.

25

Motor, wash speed low (30 rpm), counterclockwise.

26

Motor, wash speed low (30 rpm), clockwise.

27

Motor, wash speed high (48 rpm), counterclockwise.

28

Motor, wash speed high (48 rpm), clockwise.

29

Distribution speed (90 rpm), clockwise.

31

Extraction, low (550 rpm), clockwise.

32

Extraction, medium (700 rpm), clockwise.

33

Extraction, high (1000 rpm), clockwise.

34

Extraction, high (1000 rpm), clockwise.

35

Display, test of segments, LED test, and buzzer.

36

Buzzer

«
...
58
59
60
61
62
...
»

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов