manualshive.com logo in svg

Milnor Emerald EX-15, Руководство по эксплуатации и техническому обслуживанию, Страница: 33 / 87

Поделиться
Скачать
Milnor Emerald EX-15 Скачать руководство пользователя страница 33

29

Quick-Wash

On starting the machine, the door will automatic-
ally be locked, the drain valve closed.

As the main wash is started, the drain valve
closes, detergent is admitted and warm water is
filled to the level determined by the level control.

On reaching this level, hot water is closed.

The water level controlled machine will now wash
the fabrics for five minutes. The machine is then
emptied.

Cold water is filled for the first rinse which lasts
one minute.

Then comes the second rinse in cold water,
whereafter the third rinse is started.

Fabric softener is automatically admitted during
the third rinse. The fabrics are rinsed with cold
water for two minutes followed by a extraction of
three minutes duration.

             QUICK-WASH

Time

Temp.

(Min.)

Prewash

Drain

Prewash

Detergent 1

Drain

Mainwash

5

Warm

Detergent 2

Drain

0.7

Extraction

0.5

Rinse 1

1

Cold

Drain

1

Extraction

Rinse 2

1

Cold

Drain

1

Extraction

0.5

Rinse 3

2

Cold

Detergent 3

Drain

0.8

Extraction

4

Total time

17

(water fill time
not included)

Wash Cycles

49

Fig.

49

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов