Milnor Emerald EX-15 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 87

Milnor Emerald EX-15 Скачать руководство пользователя страница 59

55

Built-in service program

The machine has a built-in service program to
facilitate function checking and fault-finding.

This program may only be used by train-
ed and authorized service personnel.

To switch on service mode

•

Remove the machine top and the cover for
the program unit circuit board.

•

Press the service switch. This switch is on the
left-hand edge of the circuit board when
viewed from the machine front. The display
will now show SE, which means that the
service program is activated.

Controls in service mode

Now some of the buttons switch to being
number keys (1 to 9). The start button becomes
an ON/OFF key. The various machine functions
can be tested using numerical codes (see table
on next page).

The LEDs to the left of the display show which
input signals to the program control unit are
active.

To switch off service mode

Press the service switch again, or switch off the
machine power supply.

Service button

3400

3385

3429

Fig

81

Fig

82

Fig

83

Fig

81

83

Service program

82

81

A

1

1

4

3

2

6

5

8

7

9

Key switch for price = zero
Coin slot 1

Coin slot 2
Price programming button

Switch in door lock
Door status switch
Remote start, e.g. by external
timer

«
...
57
58
59
60
61
...
»

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов