Milnor Emerald EX-15 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 87

Milnor Emerald EX-15 Скачать руководство пользователя страница 19

15

•

Now the display will show the clock symbol
and two digits. The two digits are the time
left before the wash will be finished.

The two digits indicating time left will not
appear when the machine is first installed.
Each program needs to have been used at
least once before the time left will be
displayed.

•

For 5 minutes immediately after START is
pressed the colon character (

:

) will flash on

the display. As long as this character is still
flashing a new program can be selected
(without the drain opening). This means you
still have the chance to change the setting if
the wrong program has been selected. Do
as follows:

•

Press START.

•

Select a new program.

•

Press START again after making any
change in the program selected.

If for any reason you wish to halt the wash
cycle for a time, press the START button for a
moment or two. The program will be suspended
and the drain will remain closed.

To restart the program, press the START
button again briefly.

Fig.

25

Operating Instructions

Fig.

26

Fig.

27

27

3435

START

3434

26

Hot

1

3141

25

«
...
17
18
19
20
21
...
»

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов