Milnor Emerald EX-15 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 87

Milnor Emerald EX-15 Скачать руководство пользователя страница 67

63

Trouble shooting

Error codes which may arise on the control panel display

Error code/symptoms

Fault-finding

Cause/Action

04E

Temperature sensing device
indicates temperature below -
5

°

C (continuity fault).

Turn the machine’s wall switch off and on again.
Start a program.

Error code returns

No error code

Short-circuit the temperature sensor by the
sensor. Turn the machine’s wall switch off and
on again. Start a program. Check whether the
error displayed is 04E or 05E.

04E

05E

Remove PCB connector X74 on program control
unit PCB. Short-circuit inputs 1 and 2. Turn the
machine’s wall switch off and on again. Start a
program. Check whether the error displayed is
04E or 05E.

04E

05E

2

X74

1

2316

3399

Temperature
sensor

Check
voltage

Transient fault.

Temperature sensor faulty.
Replace sensor.

Fault in temperature sensing
device on program control
unit PCB. Replace PCB.

Rough values on the temp.
sensor

T (

°

C)

R (ohm)

19

6100

20

5850

21

5600

22

5350

23

5100

Fault in wiring to temperature
sensor. Check wiring and
replace if necessary.

«
...
65
66
67
68
69
...
»

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов