Milnor Emerald EX-15 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 87

Milnor Emerald EX-15 Скачать руководство пользователя страница 4

Contents

Introduction ...................................................................... 1
Technical data .................................................................. 2
Installation ........................................................................ 5
Safety rules .................................................................... 12
Operating instructions .................................................... 13
Programming .................................................................. 19
Wash cycles ................................................................... 22
Mechanical and electrical design ................................... 31
Serviceprogram .............................................................. 55
Trouble shooting ............................................................ 58
Maintenance ................................................................... 83

Safety instructions

•

This machine is designed for water washing only.

•

This machine must not be used by children.

•

All installation operations are to be carried out by qualified
personnel. Licensed personnel are necessary for all electric
power wiring.

•

The interlock of the door must be checked daily for proper
operation and must not be bypased.

•

All seepage in the system, due to faulty gaskets etc., must be
repaired immediately.

•

All service personnel must be fully familiar with the operating
manual before attempting any repair or maintenance of the
machine.

•

This machine must not be sprayed with water, otherwise short
circuiting may occur.

•

Fabric softeners with volatile or inflammable fluids are not to
be used in the machine.

The manufacturer reservs the right to make changes to design and
material specifications.

EX-15 ES, EX-25 ES

«
...
2
3
4
5
6
...
»

Содержание Emerald EX-15
























































































Отзывы:

Нет отзывов